Acer Network Device Altos R520 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Acer Network Device Altos R520 herunter. Acer Network Device Altos R520 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 184
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen

Inhaltsverzeichnis

Seite 1 - Acer Altos R520 Series

Acer Altos R520 SeriesUser’s Guide

Seite 3 - FCC notice

This chapter gives information about the system BIOS and discusses how to configure the system by changing the settings of the BIOS parameters.

Seite 4 - Laser compliance statement

91BIOS setup BIOS setup is a hardware configuration program built into the system's Basic Input/Output System (BIOS). Since most systems are alre

Seite 5 - Important safety instructions

4 BIOS setup92Entering BIOS setupPower on the server to start the system POST process. During bootup, press F2 to enter the BIOS setup screen. Note:

Seite 6

93•Press F1 for General Help on using the BIOS setup.•Press F9 to load the default configuration.•Press F10 to save changes and close the BIOS setup.•

Seite 7 - Contents

4 BIOS setup94Using the BIOS menusMainThe Main menu displays basic and important information about the system. These information are necessary for tr

Seite 8 - 5 Troubleshooting 127

95Processor Specification of the processor currently installed in the server. Total Memory Indicates the size of the system memory.Quiet Boot When Ena

Seite 9 - Appendix A: Acer Altos R520

4 BIOS setup96AdvancedThe Advanced menu contains parameter values that define how the system behaves on startup. Warning! Be cautious in setting para

Seite 10

97ProcessorThe Processor submenu displays CPU settings such as type, actual speed, cache size and other CPU related settings. Parameter Description Op

Seite 11 - 1 System tour

4 BIOS setup98Virtualization TechnologyEnables or disables the system to run multiple operating systems and applications in different partition. Dis

Seite 12

99Processor # InformationThe screen below appears when you select the Processor #1 or 2 Information menu.

Seite 14 - 1 Supported when available

4 BIOS setup100MemoryThe Memory submenu displays the total amount of memory installed, the number of memory modules installed, and the current memory

Seite 15

101Configure Memory RAS and PerformanceThe screen below appears when you select the Configure Memory RAS and Performance menu. This submenu allows you

Seite 16 - System fan

4 BIOS setup102Memory MIrroring PossibleIndicates whether a mirrored configuration is possible with the current installed memory. If No is displayed,

Seite 17 - Front bezel

103ATA ControllerThe ATA Controller submenu lets you define the parameter settings related to the hard disk(s). Parameter Description OptionOnboard P

Seite 18 - Front panel

4 BIOS setup104AHCI Mode Enables or disables access to all six SATA connectors via the AHCI (Advanced Host Controller Interface) Option ROM. AHCI is

Seite 19 - Rear panel

105Mass Storage The Mass Storage submenu displays the status of the mass storage controller. Parameter Description OptionSAS Controller Enables or

Seite 20 - Internal components

4 BIOS setup106Serial PortThe Serial Port submenu lets you define the parameter settings for the system’s serial port. Parameter Description OptionSe

Seite 21 - System boards

107USB ConfgurationThe USB Configuration submenu allows you specify settings for USB devices. Address Set the base I/O address for the serial B port.

Seite 22

4 BIOS setup108Legacy USB SupportEnables or disables the support for legacy USB devices. EnabledDisabledAutoPort 60/64 EmulationEnables or disables t

Seite 23 - Backplane board

109PCIThe PCI submenu lets you specify settings that are related to the onboard controllers. enable or disable the ROM scan of a device installed in t

Seite 24 - Rear view

The Acer Altos R520 is a 1U dual-core Intel Xeon- based server equipped with numerous high performance features designed to provide easy server set

Seite 25 - Mid-plane board

4 BIOS setup110Onboard NIC ROMEnables or disables both channels of the embedded LAN. Note: If disabled, NIC1 and NIC2 cannot be used to boot the syst

Seite 26

111System Acoustic and Performance ConfigurationThe System Acoustic and Performance Configuration submenu lets you set the system fan performance opti

Seite 27 - Control panel

4 BIOS setup112SecurityThe Security menu allows you to safeguard and protect the system from unauthorized use by setting up access passwords. Paramet

Seite 28 - BA F GEDC

113To set a Administrator/User password1 Use the up/down keys to highlight a password parameter (Set Administrator Password or Set User Password) then

Seite 29

4 BIOS setup114Server Management The Server Management submenu lets you specify the appropriate settings for the system’s event handling function. Th

Seite 30 - System LED indicators

115Resume on AC Power LossDefines the mode of operation if a power loss occurs.When set to Stay Off, the system remains off after power shutdown.When

Seite 31

4 BIOS setup116Console RedirectionThe Console Redirection submenu lets you enable or disable the console redirection parameters for server managemen

Seite 32

117System InformationThe System Information submenu displays basic information about the server unit.

Seite 33

4 BIOS setup118Boot OptionsThe Boot Options menu allows you to set the network device priority during system bootup. It also displays information abo

Seite 34

119CD-ROM Order Specifies the boot device priority sequence for available CD drives. Floppy Order Specifies the boot device priority sequence for avai

Seite 35 - LAN port LED indicators

3System featuresListed below are the key features of the Acer Altos R520 server. PerformanceProcessor• Supports two dual-core or quad-core Intel® Xeon

Seite 36

4 BIOS setup120Network Device #The Network Device # submenu lets you specify the preferred settings for system bootup. Parameter Description Op

Seite 37 - System jumpers

121Boot ManagerThe Boot Manager menu lets you set the device priority during system bootup. The server will attempt to boot from the first device on t

Seite 38 - 1 System tour

4 BIOS setup122Error ManagerThe Error Manager menu lets you view the system POST errors detected by the system.

Seite 39 - 2 System setup

123ExitThe Exit menu displays the various options to quit from the BIOS setup. Highlight any of the exit options then press Enter. Parameter Descripti

Seite 40

4 BIOS setup124Save as User Default ValuesSaves current values to be restored later. Restore User Default ValuesRestores previously saved user defaul

Seite 41 - Setting up the system

125Upgrading the BIOSThe upgrade utility allows you to upgrade the BIOS in the flash memory. To prepare to upgrade the BIOS, you need to record the cu

Seite 44 - Power-on problems

This chapter provides possible solutions for specific problems. If you cannot correct the problem, contact your local Acer representative or authorize

Seite 45 - Configuring the system OS

129TroubleshootingThis chapter helps you identify and solve problems that might occur while you are using the system.For any issue, first ensure that

Seite 46 - Turning off the system

1 System tour4• For SATA models, the embedded SATA controller support- Passive mid-plane board- Six onboard SATA connectors - Up to six hot-plug 2.5”

Seite 47 - 3 System upgrade

5 Troubleshooting130First steps checklist• AC power available at the wall outlet?• Are the power supplies plugged in? Check the AC cable(s) on the ba

Seite 48

131Hardware diagnostic testingThis section provides a more detailed approach to identifying a hardware problem and locating its source.Caution! Before

Seite 49 - Installation precautions

5 Troubleshooting132Confirming loading of the OSOnce the system boots up, the operating system prompt appears on the screen. The prompt varies accord

Seite 50 - 3 System upgrade

133Server boot does not complete POSTDo the following:• Make sure the CPU is properly seated. • Check the BIOS release notes to ensure the BIOS instal

Seite 51 - Opening the server

5 Troubleshooting134ODD tray cannot be ejected.• Insert the tip of a paperclip into the small hole on the ODD drive. Slowly pull the tray out from th

Seite 52 - To install the front bezel:

135• Make sure the memory modules have been populated according to the system requirements. External device connected to a USB connector does not work

Seite 53 - To remove the top cover:

5 Troubleshooting136The controller stopped working when an adapter was installed.• Make sure the cable is connected to the port from the onboard netw

Seite 54 - To install the top cover:

137• If other software runs correctly on the system, contact your vendor about the defective software.No characters appear on the screen.Check the fol

Seite 55 - To remove the CPU air duct:

5 Troubleshooting1385 If you do not receive a beep code and characters do not appear, the video display monitor or video controller may have failed.

Seite 56 - To install the CPU air duct:

139Error beep codesBIOS POST error beep codesThe following table lists the POST error beep codes. Prior to system video initialization, BIOS uses thes

Seite 57 - Removing the CPU air dam

5Networking• Intel ESB2 I/O controller • Intel 82563EB Gigabit controller with dual ports• Supports Intel I/O Acceleration TechnologyPCI I/O • Low pro

Seite 58

5 Troubleshooting140Troubleshooting BIOS POST error beep codesThe following table lists the possible beep codes thay may occur while using the system

Seite 59

141ARMC/3 module error beep codesIn addition to the beep codes above, additional beep codes are provided if an ARMC/3 module is installed. The managem

Seite 60 - Determining drive status

5 Troubleshooting142Diagnostic POST code LEDsDuring the system boot process, BIOS executes a number of platform configuration processes, each of whic

Seite 61 - To remove a HDD:

1430x13h OFF OFF G A SMM initializationChipset0x21h OFF OFF R G Initializing a chipset componentMemory0x22h OFF OFF A OFF Reading configuration data f

Seite 62 - To install a HDD:

5 Troubleshooting144ATA / ATAPI / SATA0x5Ah G R G R Resetting PATA / SATA bus and all devices0x5Bh G R G A Reserved for ATASMBUS0x5Ch G A OFF R Reset

Seite 63

1450x9Bh A OFF G A Enabling the mouseFixed Media0xB0h R OFF R R Resetting fixed media device0xB1h R OFF R A Disabling fixed media device0xB2h R OFF A

Seite 64

5 Troubleshooting1460xDB A R G A Trying boot device selection 0xDC A A OFF R Trying boot device selection 0xDE A A G R Trying boot device selection 0

Seite 65

1470xF8h ARRROperating system has requested EFI to close boot services (Exit Boot Services has been called)0xF9h A R R A Operating system has switched

Seite 66

5 Troubleshooting148

Seite 67

Appendix A: Acer Altos R520rack installation guide

Seite 68 - To remove a PCI card:

1 System tour6• Rear• PS/2 keyboard port• PS/2 mouse port• Serial B port (RJ-45)• Two Gigabit (10/100/1000 Mbps) LAN ports (RJ-45) • Server managemen

Seite 69 - To install a PCI card:

This appendix shows you how to set up the Acer Altos R520 server in a rack mount configuration.

Seite 70

151Setting up the system rackImportant! Observe the electrostatic discharge (ESD) precautions indicated on page 39 when perfoming the following proced

Seite 71 - Upgrading the CPU

Appendix A: Acer Altos R520 rack installation guide152• Elevated operating ambient temperature The maximum operating temperature of the system is 35

Seite 72

153System rack installation The Acer Altos R520 server should be mounted into a rack. A tool-less rack rail and CMA (cable management arm) kit is avai

Seite 73

Appendix A: Acer Altos R520 rack installation guide154Vertical mounting hole patternThe four vertical rails of the system rack contain mounting holes

Seite 74

155Installing the system into the rackCaution! To minimize the chances of injuries, make sure that two or more people help in installing the server. T

Seite 75 - To remove a CPU:

Appendix A: Acer Altos R520 rack installation guide156(3) Do the same thing to the other mounting rail.Caution! To avoid personal injury, care should

Seite 76

1573 Install the mounting rails to the rack posts. (1) Determine the vertical position in the rack. Refer to “Vertical mounting hole pattern” on page

Seite 77 - Upgrading the system memory

Appendix A: Acer Altos R520 rack installation guide158(6) Fully extend the mounting rails on the rack.

Seite 78

1594 Install the server into the rack.Caution! To avoid personal injury, care should be taken when pressing the inner rail release latches and sliding

Seite 79 - Mirrored configuration

7External and internal structureFront bezelThe front bezel provides an interface for system management via status LED indicators. The light pipes on t

Seite 80 - Memory configuration overview

Appendix A: Acer Altos R520 rack installation guide1605 Attach the CMA (cable management arm) to the rear of the server.The CMA allows you to tie-wra

Seite 81 - Mirrored memory configuration

161(6) Connect the power, peripheral and networking cables into their appropriate ports. Refer to “Connecting peripherals” on page 32 for detailed ins

Seite 82 - Memory sparing configuration

Appendix A: Acer Altos R520 rack installation guide162

Seite 83 - To install FBDIMMs:

Appendix B: RAIDconfiguration

Seite 84 - To remove FBDIMMs:

This appendix gives an overview of the different RAID configuration that you can use to configure RAID settings for the system hard drives.

Seite 85

165Configuring integrated SAS RAIDThis section briefly shows how to create RAID volume with integrated SAS RAID when the hardware RAID components: RAI

Seite 86

Appendix B: RAID configuration1665 Select the RAID Level you want to configure. Create the logical volume by specify the size at Select Size and clic

Seite 87

167Configuring the integrated SAS SW RAIDThis section briefly shows how to create RAID 1 (mirror) volume with integrated SAS SW RAID function.Load BIO

Seite 88

Appendix B: RAID configuration1682Select New Configuration from the Configuration menu and select Yes to continue. An array selection menu displays t

Seite 89 - To remove an ARMC/3 module:

169Configuring the onboard SATA RAIDThis section briefly shows how to create RAID 1 (mirror) volume with onboard SATA RAID function.Load BIOS default

Seite 90 - To install an ARMC/3 module:

1 System tour8Front panel * The Acer Altos R520 dual-purpose bay supports either the standard control panel or two2.5” hot-plug HDD drives. Item Com

Seite 91

Appendix B: RAID configuration1702Select New Configuration from the Configuration menu and select Yes to continue. An array selection menu displays t

Seite 92

171IndexAARMC/3 moduleinstalling 80removing 79specifications 5BBIOS menusAdvanced 96ATA Controller 103Mass Storage 105Memory 100C

Seite 93 - AF000904

172NNIC moduleinstalling 81removing 79Oopening the system 41installing the front bezel 42installing the top cover 44removing the front

Seite 94 - To install the RAID BBU:

173system jumpers 27system memoryreconfiguring 75system tour 1system upgrade 37ESD precautions 39installation precautions 39post-ins

Seite 96

9Rear panel 1 The system power can be configured to support redundant (1+1) and non-redundant (1+0)configuration. 2 Reserved for remote management of

Seite 97

Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such cha

Seite 98

1 System tour10Internal components Item Component Item ComponentA Power distribution board G Memory modules B Power distribution board coverH CP

Seite 99 - 4 BIOS setup

11System boardsMainboardThe mainboard becomes accessible once you open the system. It should look like the figure shown below.Item Description Item D

Seite 100

1 System tour12C Diagnostic POST code indicatorsY Dual port USB 2.0 connectorD Full height PCI riser slot Z SATA 0 connectorE Low profile PCI riser s

Seite 101 - BIOS setup

13Backplane boardSAS/SATA backplane boardThe backplane board installed on the rear side of the hot-plug drive bay provides support for both SAS and SA

Seite 102 - Entering BIOS setup

1 System tour14Rear view Item Description Item DescriptionA Control panel connector D Mid-plane connectorsB USB connector E Backplane power connecto

Seite 103

15Mid-plane boardThe mid-plane boad serves as the primary interface between the mainboard, backplane, and control panel. It is used to determine the d

Seite 104 - Using the BIOS menus

1 System tour16Passive mid-plane board (SATA model)The passive mid-plane board is used to provide SATA support for the onboard SATA controller and si

Seite 105

17Control panelThe Acer Altos R520 server supports either the mini control panel, providing basic functionality, or the standard control panel, which

Seite 106 - Advanced

1 System tour18Standard control panel (optional) Item Component Item ComponentA LAN 2 activity indicator G System ID indicatorB LAN 1 activity indica

Seite 107 - Processor

19Control panel button function overviewThe following table list and describe the function of the control buttons available on the control panel. Con

Seite 108

iiiNoticesFCC notice Class A equipmentThis device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15

Seite 109 - Processor # Information

1 System tour20System LED indicatorsThis section describes the different LED indicators located on • Mainboard• Control panel• Hot-plug HDD carrier•

Seite 110

21Mainboard diagnostic LED indicators Item Description Color State DescriptionA Diagnostic POST code indicatorsDuring the system boot process, BIOS ex

Seite 111

1 System tour22B System ID indicatorBlue On The system ID buton on the control panel is activated Off System identification is disabledBlink Appropri

Seite 112

23Systemstatus indicator (cont.)Amber On Critical or non-recoverable condition• DIMM failure when there is one DIMM present• Run-time memory uncorrect

Seite 113 - ATA Controller

1 System tour24Control panel LED indicators The following table list and describe the LED indicators available on the mini or optional standard co

Seite 114

25Hot-plug HDD LED indicators There are two status LED indicators mounted for each hot-plug HDD carrier. The table below list the possible drive sta

Seite 115 - Mass Storage

1 System tour26Hot-plug power supply module LED indicatorThe table below list and describe the bi-color LED indicator located on the power supply mod

Seite 116 - Serial Port

27System jumpers Jumper name Settings FunctionJ1D2Password clear1-2 (default)2-3Password enabledPassword disabled/clearedJ1D3Clear CMOS1-2 (default)2-

Seite 118

2 System setup

Seite 119

ivCaution! Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Commun

Seite 120

This chapter gives you instructions on how to set up the system. Procedures on how to connect peripherals are also explained.

Seite 121

31Setting up the systemPre-installation requirementsSelecting a siteBefore unpacking and installing the system, select a suitable site for the system

Seite 122 - Security

2 System setup32Connecting peripheralsCaution! The server operates on 100-127/200-240 VAC only. Do not connect the system to an incorrect voltage sou

Seite 123 - To remove the User password

33Turning on the systemAfter making sure that you have properly set up the system and connected all the required cables, you can now power on the syst

Seite 124 - Server Management

2 System setup34Power-on problemsIf the system does not boot after you have applied power, check the following factors that might have caused the boo

Seite 125

35Configuring the system OSThe Acer Altos R520 server comes with Acer EasyBUILDTM that allows you to conveniently install your choice of operating sys

Seite 126 - Console Redirection

2 System setup36Turning off the systemThere are two ways to turn off the server. These include:• Software power offIf you are using a Windows OS on y

Seite 128 - Boot Options

This chapter discusses the precautionary measures and installation procedures you need to know to upgrade the system.

Seite 129

39Installation precautionsBefore you install any server component, we recommend that you read the following sections. These sections contain important

Seite 130 - Network Device #

vImportant safety instructionsRead these instructions carefully. Save these instructions for future reference.1 Follow all warnings and instructions m

Seite 131 - Boot Manager

3 System upgrade40Warning! Failure to properly turn off the server before you start installing components may cause serious damage. Do not attempt th

Seite 132 - Error Manager

41Opening the serverCaution! Before you proceed, make sure that you have turned off the system and all peripherals connected to it. Read the “Pre-inst

Seite 133

3 System upgrade42To install the front bezel:1 Line up the center notch on both ends of the bezel with the center guide on the rack handles. 2 Slide

Seite 134

43Removing and installing the top coverTo remove the top cover:1 Observe the ESD precautions and pre-installation instructions described on page 39.2

Seite 135 - Upgrading the BIOS

3 System upgrade44To install the top cover:1 Observe the ESD precautions and pre-installation instructions described on page 39.2 Place the top cover

Seite 136 - 4 BIOS setup

45Removing and installing the CPU air ductCaution! Always operate your server with the CPU air duct installed to ensure reliable and continued operati

Seite 137 - 5 Troubleshooting

3 System upgrade46To install the CPU air duct:1 Observe the ESD precautions and pre-installation instructions described on page 39.2 Place the CPU ai

Seite 138

47Removing the CPU air damTo remove the CPU air dam:Important: Do not remove the CPU air dam from the CPU air duct except when installing a second CPU

Seite 139 - Troubleshooting

3 System upgrade48Removing and installing the power distribution board coverTo remove the power distribution board cover:You will need to remove the

Seite 140 - First steps checklist

49To install the power distribution board cover:1 Observe the ESD precautions and pre-installation instructions described on page 39.2 Lower the power

Seite 141 - Hardware diagnostic testing

vid If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operatin

Seite 142 - Confirming loading of the OS

3 System upgrade50Configuring the storage devices The system supports 2.5-inch storage devices. It accommodates slim-line optical drives and dependi

Seite 143

51To remove a HDD:1 Observe the ESD precautions described on page 39.2 If you are removing a failed HDD, determine which drive has failed by checking

Seite 144 - ODD drive cannot read a disc

3 System upgrade52To install a HDD: Note: To puchase a HDD carrier, contact your local Acer representative. 1 Perform steps 1 to 4 listed on the “To

Seite 145 - Problems with the network

538 When the lever begins to close by itself, push on it to lock the drive assembly into place (B). Removing and installing a slim-line optical driveN

Seite 146 - 5 Troubleshooting

3 System upgrade542 Press the blue release lever to unlock the optical drive tray (A) and slide the optical drive tray out through the front of the s

Seite 147

555 Install the plastic guide on the rear of the optical device, then secure it with the two screws that came with the optical drive kit.6 Slide the o

Seite 148

3 System upgrade56Removing and installing a PCI riser assemblyNote: The PCI riser assembly includes an intrusion switch that engages the system cover

Seite 149 - Error beep codes

575 Lift the riser assembly from the chassis. 6 Place the riser assembly on a clean, static-free work surface. 7 If you need to replace PCI cards. See

Seite 150

3 System upgrade58To install the PCI riser assembly:1 Observe the ESD precautions and pre-installation instructions described on page 39.2 Lower the

Seite 151

595 When removing a full height PCI card, open the full length PCI card retention clip on the front of the riser assembly by rotating it 90 degrees ou

Seite 152 - Diagnostic POST code LEDs

ContentsNotices iiiFCC notice iiiLaser compliance statement ivImportant safety instructions v1 System tour 1System features 3Performance 3External

Seite 153 - G=Green, R=Red, A=Amber

3 System upgrade605 When installing a full height PCI card, open the full length PCI card retention clip on the front of the riser assembly by rotati

Seite 154

61Upgrading the CPUThe server supports two dual-core or quad-core Intel Xeon processors 5000 sequence with system bus speeds of 667 MHz, 1066 MHz or 1

Seite 155

3 System upgrade625 Push the socket retainer lever handle down and away from the socket to release it (A), then pull the lever to a fully open, uprig

Seite 156

63 10 Remove the protective socket cover by grasping the socket cover tab (A) and pulling it away from the load plate (B). 11 Store the protective s

Seite 157

3 System upgrade6413 If the heat sink does not have thermal grease on the bottom, apply thermal grease to the heat sink base. 14 Install the heatsink

Seite 158

65To remove a CPU:If you are replacing a CPU on the system, the heat sink must first be removed. Important: Before removing a CPU from the mainboard,

Seite 159 - Appendix A: Acer Altos R520

3 System upgrade66(3) Lift the heat sink from the processor. Caution! If it does not pull up easily, twist the heat sink again. Do not force the heat

Seite 160

67Upgrading the system memoryAcer Altos R520 server supports eight DDR2 fully buffered DIMM slots with four FBDIMM memory channels. Each channel can s

Seite 161 - Setting up the system rack

3 System upgrade68Memory module installation guidelinesThe following rules apply when installing fully-buffered memory modules to the server:• The sy

Seite 162

69Memory module population orderThe tables below list the suggested DDR2 FBDIMM module population for standard, mirrored or sparing configuration. Sta

Seite 163 - System rack installation

viiiRemoving the CPU air dam 47Removing and installing the power distribution board cover 48Configuring the storage devices 50Removing and installing

Seite 164

3 System upgrade70Sparing configurationMemory configuration overviewThe system supports the following memory configuration that allow flexibility in

Seite 165

71Standard memory configurationThe system is capable of supporting a minimum of only one FBDIMM installed on the DIMM A1 slot. However, for system pe

Seite 166

3 System upgrade72To upgrade to a four FBDIMM mirrored memory configuration, four additional FBDIMMs must be added to the system. All four memory mod

Seite 167

73• The following FBDIMM slots must be identical in organization, size and speed.• The following DIMM slots need not be identical in organization, siz

Seite 168

3 System upgrade744 Open the clips on the DIMM slot(s) (A). 5 Align (B) then insert the FBDIMM into the socket (C). 6 Press the holding clips inward

Seite 169

75Caution! Use extreme care when removing DIMMs. Too much pressure can damage the connector. Apply only enough pressure on the plastic levers to relea

Seite 170

3 System upgrade76Installing and removing a power supply moduleThe server has two power supply module bays on the rear panel that accept hot-plug pow

Seite 171

77To install a second power supply module:1 Remove the top cover. Perform the instructions described in “To remove the top cover” section on page 43.2

Seite 172

3 System upgrade78To remove a power supply module:Caution! Power supply hot-plug operations should be performed only if a failure occurs in the power

Seite 173 - Appendix B: RAID

79Removing and installing an ARMC/3 moduleThe optional ARMC/3 module provides server management firmware and functionality to the system. To remove an

Seite 174

ixHardware diagnostic testing 131Verifying proper operation of key system lights 131Specific problems and corrective actions 132Error beep codes 139BI

Seite 175 - Load BIOS default setting

3 System upgrade805 Pull up the module to remove it from the connector (B). 6 Observe the post-installation instructions described on page 40.To inst

Seite 176 - Assigning a Hot Spare Disk

814 Attach the module to the ARMC/3 module connector on the mainboard and snap the standoff into the matching hole on the mainboard (B). 5 Install the

Seite 177 - Create RAID 1 volume

3 System upgrade82Installing and removing the SAS hardware RAID componentsThe system supports SAS hardware RAID through the active mid-plane and back

Seite 178 - Initial RAID Volume

836 Open the clips on the slot (B). 7 Align then insert the RAID cache into the slot (C). 8 Press the holding clips inward to lock the RAID cache in p

Seite 179

3 System upgrade846 Gently pull the RAID cache upward to remove it from the slot (C). 7 Close the clips. 8 Store the RAID activation key and RAID ca

Seite 180

854 Close and latch the BBU case lid. 5 Align the two hooks on the underside of the RAID BBU with the matching chassis tabs, then slide toward the pow

Seite 181

3 System upgrade864 Slide the RAID BBU forward and lift from the chassis (B). 5 Store the RAID BBU in an antistatic protective wrapper. 6 Observe the

Seite 182

87Installing and removing the SATA software RAID activation keyThe system supports SATA software RAID 5 through the installation of a RAID activation

Seite 183

3 System upgrade88To remove the RAID activation key:1 Observe the ESD precautions and pre-installation instructions described on page 39.2 Remove the

Seite 184

4 BIOS setup

Kommentare zu diesen Handbüchern

Keine Kommentare