Acer Network Device Altos R520 Bedienungsanleitung Seite 83
- Seite / 184
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
73
• The following FBDIMM slots must be identical in organization,
size and speed.
• The following DIMM slots need not be identical in
organization, size and speed.
• Sparing should be enabled in the BIOS setup utility
• BIOS will configure rank sparing mode.
• The largest memory size among the DIMM pairs (DIMM_A1,
DIMM_B1) and (DIMM_A2, DIMM_B2) and (DIMM_C1,
DIMM_D1) and (DIMM_C2, DIMM_D2), will be selected as the
spare pair units.
Note: After upgrading system memory to this feature, the
memory RAS setting in the BIOS setup must be set to Sparing
configuration. Refer to the BIOS setup’s Configure Memory RAS
and Performance screen on page 101 for more information.
To install FBDIMMs:
Caution! Use extreme care when installing a FBDIMM. Applying
too much pressure can damage the connector. FBDIMMs are keyed
and can be inserted in only one way.
Note: The number labels next to the FBDIMM slots correspond to
proper installation sequence.
1 Observe the ESD precautions and pre-installation instructions
described on page 39.
2 Remove the CPU air duct. Perform the instructions described in “To
remove the CPU air duct” section on page 45.
3 Locate the DIMM slots on the mainboard.
• DIMM slots A1 and B1 • DIMM slots C1 and D1
• DIMM slots A2 and B2 • DIMM slots C2 and D2
• DIMM slots A1 and A2 • DIMM slots C1 and C2
• DIMM slots B1 and B2 • DIMM slots D1 and D2
- Acer Altos R520 Series 1
- FCC notice 3
- Laser compliance statement 4
- Important safety instructions 5
- Contents 7
- 4 BIOS setup 89 8
- 5 Troubleshooting 127 8
- Appendix A: Acer Altos R520 9
- 1 System tour 11
- System features 13
- 1 Supported when available 14
- Operating system and software 16
- Power supply 16
- System fan 16
- Front bezel 17
- Front panel 18
- Rear panel 19
- Internal components 20
- System boards 21
- Backplane board 23
- Rear view 24
- Mid-plane board 25
- Control panel 27
- BA F GEDC 28
- System LED indicators 30
- LAN port LED indicators 35
- System jumpers 37
- 1 System tour 38
- 2 System setup 39
- Setting up the system 41
- Connecting peripherals 42
- Turning on the system 43
- Power-on problems 44
- Configuring the system OS 45
- Turning off the system 46
- 3 System upgrade 47
- Installation precautions 49
- 3 System upgrade 50
- Opening the server 51
- To install the front bezel: 52
- To remove the top cover: 53
- To install the top cover: 54
- To remove the CPU air duct: 55
- To install the CPU air duct: 56
- Removing the CPU air dam 57
- Determining drive status 60
- To remove a HDD: 61
- To install a HDD: 62
- To remove a PCI card: 68
- To install a PCI card: 69
- Upgrading the CPU 71
- To remove a CPU: 75
- Upgrading the system memory 77
- Standard configuration 79
- Mirrored configuration 79
- Memory configuration overview 80
- Standard memory configuration 81
- Mirrored memory configuration 81
- Memory sparing configuration 82
- To install FBDIMMs: 83
- To remove FBDIMMs: 84
- To remove an ARMC/3 module: 89
- To install an ARMC/3 module: 90
- AF000904 93
- To install the RAID BBU: 94
- To remove the RAID BBU: 95
- 4 BIOS setup 99
- BIOS setup 101
- Entering BIOS setup 102
- Using the BIOS menus 104
- Advanced 106
- Processor 107
- Processor # Information 109
- ATA Controller 113
- Mass Storage 115
- Serial Port 116
- USB Confguration 117
- Security 122
- To remove the User password 123
- Server Management 124
- Console Redirection 126
- System Information 127
- Boot Options 128
- Network Device # 130
- Boot Manager 131
- Error Manager 132
- Upgrading the BIOS 135
- 4 BIOS setup 136
- 5 Troubleshooting 137
- Troubleshooting 139
- First steps checklist 140
- Hardware diagnostic testing 141
- Confirming loading of the OS 142
- ODD tray cannot be ejected 144
- ODD drive cannot read a disc 144
- Problems with the network 145
- 5 Troubleshooting 146
- Error beep codes 149
- Diagnostic POST code LEDs 152
- G=Green, R=Red, A=Amber 153
- Appendix A: Acer Altos R520 159
- Setting up the system rack 161
- System rack installation 163
- Appendix B: RAID 173
- Load BIOS default setting 175
- Assigning a Hot Spare Disk 176
- Create RAID 1 volume 177
- Initial RAID Volume 178
Verwandte Produkte und Handbücher für Hardware Acer Network Device Altos R520
Hardware Acer 4060 Bedienungsanleitung
(99 Seiten)
(99 Seiten)
Hardware Acer WT 300 Bedienungsanleitung
(54 Seiten)
(54 Seiten)
Hardware Acer 11b Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Hardware Acer ISDN P10 Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Hardware Acer ALN-201 Bedienungsanleitung
(0 Seiten)
(0 Seiten)
Hardware Acer 500GB Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Rotel RB-1092 manuels
Manuels d'utilisation et guides de l'utilisateur pour Haut-parleurs Rotel RB-1092.
Nous fournissons des manuels en pdf 1 Rotel RB-1092 à télécharger gratuitement par type de document : Manuel du propriétaire
Kommentare zu diesen Handbüchern