search

Acer R-1200 Wartungshandbuch Seite 17

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 40
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
    •
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 16
15
R-1200
R-1201
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the key unit is defective, replace the key unit.
2. Control Unit.
The following symptoms indicate a defective control unit. Before replacing the control unit, perform
the Key unit test (Procedure K) to determine if control unit is faulty.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) To discharge high voltage capacitor, wait for 60 seconds.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.
K KEY UNIT TEST
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. To discharge high voltage capacitor, wait for 60 seconds.
4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch operates properly; that is the contacts are
closed when the door is closed and open when the door is open. If the door sensing switch is good,
disconnect the flat ribbon cable that connects the key unit to the control unit and make sure the door
sensing switch is closed (either close the door or short the door sensing switch connecter). Use the
Key unit matrix indicated on the control panel schematic and place a jumper wire between the pins
that correspond to the STOP/CLEAR pad making momentary contact. If the control unit responds by
clearing with a beep the key unit is faulty and must be replaced. If the control unit does not respond,
it is faulty and must be replaced. If a specific pad does not respond, the above method may be used
(after clearing the control unit) to determine if the control unit or key pad is at fault.
5. Reconnect all leads removed from components during testing.
6. Re-install the outer case cabinet.
7. Reconnect the power supply cord.
8. Run the oven and check all functions.
Seitenansicht 16
1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare
  • Microframe Corporation American Power Conversion Qtech Eko Brands CH Products
  • Force10 Networks Vernetzung Samsung Telefone Sony Autolautsprecher Hannspree LED-Anzeigen Asus Antivirus-Sicherheitssoftware
  • Electrolux ENN28600 Jenn-Air JGR8850 LG FC1409S2W Daewoo KR-14E5 White Rodgers 1A65W-641
  • Polk-audio RMDS-1 Bedienungsanleitung Samsung GT-E2550 Bedienungsanleitung Alto-Shaam AR-6G Bedienungsanleitung Casio SA-67 Bedienungsanleitung Euro-Pro TO241R Bedienungshandbuch