Acer X223W Bedienungsanleitung PDF herunterladen

LCD Monitor Quick Setup Guide

X223W

English

Safety Instructions

Observe the folowing safety guidelines when connection and using your monitor:

· Be sure that your monitor is electrically rated to operate with the AC power available inyour location.

· Locate your monitor near an easily accessible electrical outlet.

· Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched

with a sharp or abrasive implement.

· Put your monitor in a location with low humidity and a minimum of dust.

· Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep

the cable away from where people could trip over it.

· Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.

· To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor’s case.

· Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.

· Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be

blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface.

· Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some

other enclosed space, be sure to provide adequate ventilation.

· Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an

authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure

to unplug the monitor first. If your monitor does not operate normally-in particular, if there are any unusual sounds or smells

coming from it -unplug the monitor immediately and contact an authorized dealer or service center.

Connecting Your Monitor to a Computer

1.Connect Video Cable

a. Make sure both the monitor and computer are powered-OFF.

b. Connect the video cable to the computer.

c. (only Dual-Input Model) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other

end to the computer’s port.

2. Connect power cord

Connect the power cord to the monitor, then to a properly grounded AC outlet.

3. Connect the Audio Cable.(optional)

4. Power-ON Monitor and Computer

Power-ON the monitor first, then power-ON the computer.

This sequence is very important.

5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.

Troubleshooting Tips

No Power - The monitor’s power indicator is off.

Make sure the monitor power cable is fully inserted in the monitor’s power port and the electrical outlet.

Test the electrical oulet by plugging in a working electrical device such as a lamp.

Try another power cable on the monitor. You can use the computer’s power cable to perform this test.

No Video - The monitor’s power indicator is on but theere are no

image on the screen.

Ensure that the video connector is properly connected to the computer.

Ensure that the computer is on and functioning properly.

Turn off the monitor and check the video cable pins. Make sure no pins are bent.

Operationg Detail

Please refer to user’s guide in CD-ROM packaged with this monitor

1 2 3 4 5 6 ... 25 26

Inhaltsverzeichnis

Seite 1 - Safety Instructions

LCD Monitor Quick Setup GuideX223WEnglishSafety InstructionsObserve the folowing safety guidelines when connection and using your monitor:· Be sure th

Seite 2 - LCD Monitor Quick Setup Guide

X223WEN-4-----------------------------------------------------------------------------------------------------Warning! We do not recommend using the p

Seite 3 - LAMP Disposal

EN-5X223W· LCD MonitorUNPACKINGPlease check the following items are present when you unpack the box,and save the packing materials in case you will ne

Seite 4 - SPECIFICATION

X223WEN-6Attaching / Removing the BaseInstall:Align the release button on thebottom of the monitor with thecorrespondingslots on the bottom of the bas

Seite 5

EN-7X223WCONNECTING THE POWER CORD· Check first to make sure that the power cord you use is the correct typerequired for your area.· This monitor has

Seite 6 - TABLE OF CONTENTS

X223WEN-8Power savingThe monitor will be driven into Power Saving” mode by the control signalfrom the display controller, as indicated by the amber-co

Seite 7 - SPECIAL NOTES ON LCD MONITORS

EN-9X223WPIN NO.DESCRIPTIONPIN NO.DESCRIPTION1.Red9.+5V2.Green10.Logic Ground3.Blue11.Monitor Ground4.Monitor Ground12.DDC-Serial Data5.DDC-return13.H

Seite 8

X223WEN-1024-Pin Color Display Signal CablePINMeaningPINMeaning1.TMDS Data2-13.NC2.TMDS Data2+14.+5V Power3.TMDS Data 2/4Shield15.GND(return for+5V hs

Seite 9 - Finding your comfort zone

EN-11X223WStandard Timing TableModeResolution1VGA720 x 40070Hz2VGA640 x 48059.94Hz3MAC640 x 48066.66Hz4VESA640 x 48072Hz5VESA640 x 48075Hz6648 x 50057

Seite 10 - Developing good work habits

X223WEN-12INSTALLATIONTo install the monitor to your host system, please follow the steps as givenbelow:Steps1.1-1Connect Video Cablea. Make sure both

Seite 11 - UNPACKING

EN-13X223WUSER CONTROLSFront Panel Controls1.Power Switch:To turn ON or OFF the power.2.Power LED:Lights up to indicate the power is turned ON.3.Empow

Seite 12 - SCREEN POSITION ADJUSTMENT

LCD Monitor Quick Setup GuideX223WEnglishFCC noticeThis device has been tested and found to comply with the limits for a Class B digitaldevice pursuan

Seite 13 - CLEANING YOUR MONITOR

X223WEN-14A.Acer eColor ManagementIf selected to “Acer eColor Management “ item, will appear theAcer eColor” OSDB.USERIf selected to “USER” item, will

Seite 14 - Power saving

EN-15X223W· ADJUSTING THE PICTUREThe descriptions for function control LEDSA.Acer eColor ManagementB.USERMainMenuiconSubMenuiconSubMenuitemDescription

Seite 15 - CONNECTOR PIN ASSIGNMENT

X223WEN-16MainMenuIconSubMenuIconSub MenuItemDescriptionH. PositionAdjust the horizontal position.(available in Analog mode only)V. PositionAdjust th

Seite 16

EN-17X223WMainMenuIconSubMenuIconSub MenuItemDescriptionH. PositionAdjust the horizontal position of the OSD.V. PositionAdjust the vertical position o

Seite 17 - Standard Timing Table

X223WEN-18· Acer eColor Management OSDAcer eColor ManagementStep 1: Press “ Key “ to open the Acer eColor Management OSD andaccess the scenario modes

Seite 18 - INSTALLATION

EN-19X223W(VGA Mode)TROUBLESHOOTINGBefore sending your LCD monitor for servicing, please check the trouble-shooting list below to see if you can self-

Seite 19 - USER CONTROLS

X223WEN-20(DVI Mode)ProblemsCurrent StatusRemedyNo PictureLED ON·Using OSD, adjust brightness andcontrast to maximum or reset to theirdefault settings

Seite 20 - HOW TO ADJUST A SETTING

LCD Monitor Quick Setup GuideX223WEnglishLAMP Disposal依据中国《电子信息产品污染控制管理办法》，简称《管理办法》或《China RoHS》之规定，列出宏碁电子信息产品中可能含有的有毒或有害物质的名称及含量于以下表格中。显示器（液晶及 CRT）

Seite 21 - A.Acer eColor Management

LCD Monitor Quick Setup GuideX223WEnglishSPECIFICATIONLCD PanelDriving systemTFT Color LCDSize22.0" WPixel pitch0.282mm( H )x 0.282mm( V )Brightn

Seite 22

LCD Monitor Quick Setup GuideX223WEnglishSPECIFICATIONEnvironmentalConsiderationsOperating Temp: 50 to 350CStorage Temp.: -200 to 600COperating Humidi

Seite 23

TABLE OF CONTENTSSpecial notes on LCD monitors...1Information for your safety and comfort...

Seite 24

EN-1X223WSPECIAL NOTES ON LCD MONITORSThe following symptoms are normal with LCD monitor and do not indicate aproblem.NOTES· Due to the nature of the

Seite 25 - TROUBLESHOOTING

X223WEN-2Information for your safety and comfortSafety instructionsRead these instructions carefully. Keep this document for future reference. Follow

Seite 26 - (DVI Mode)

EN-3X223WProduct servicingDo not attempt to service this product yourself, as opening or removing covers mayexpose you to dangerous voltage points or