Acer SCSI/VGA Combo Card Technical Information

Aspire T650/E500AcerPower F5Service Guide

Chapter 1 3Remark: ULI M1573 ( for reference)The M1573 integrates a High Definition (HD) Audio/AC'97 Host Controller, 2-channel dedicated Ultra-6

3. Disconnect 12V power cable “ PD” and CPU fan power cable from the M/B. 4. Disconnect the 4 Pin power cable “PE” f

7. Disconnect the “PB” power cable from the master HDD, “PC” from the slave HDD. 8. Disconnect the two HDD SATA cabl

11. Disconnect the ODD&FDD IDE and P1 power cable from the M/B connector. Remove the Memory Loose the DIMM Latch

Remove the CD-ROM, Floppy, Card-reader and HDD 1. Release the HDD-Holder, meanwhile pull the master HDD out of the chassis. 2.

Release the ODD-Holder, meanwhile pull the Slave ODD out of the chassis, then the Master one. Removing the USB Module Remove th

Remove the Mainboard Remove the eight screws and remove the Mainboard shown bellow. Remove the Power-supply Remove the four s

AcerPower F5 Standard Reassembly Procedure Install the Power-supply Fit the Power-supply into the chassis, then fasten the four screws shown bellow

Install the System Fan Fit the System Fan into the chassis , then fasten the four screws shown bellow. Install the SPDIF Module

Install the CD-ROM, Floppy, Card-reader Module and HDD 1.Install the master ODD into the first ODD location, then install the slave ODD into the secon

5. Install the master HDD into the second HDD location, then slide the lock handle the lock the HDD. Install the front bezel Lead t

4 Chapter 1Features CPU T Socket Type : Intel Socket TT Supports Intel Pentium D FSB 800MHZT Supports Intel Pentium 4 Prescott 775 / FSB 533/800MHzT S

2.Insert the memory2 into the DIMM SLOT2 shown here. Connect the Cables 1. Connect the ODD&FDD IDE and P1 power cable to the

3. Connect the LED cable ASSY to the M/B Connector. 4. Connect the two HDD SATA cables to the HDDs and M/B connector.

7. Connect the ODD IDE cable to the master & slave ODD. 8. Connect the 4 Pin power cable “PE” to the master ODD, “PF” t

11. Connect the SPDIF and AUDIO cables. Install the ADD ON Cards 1. Insert the Modem Card into the PCI SLOT3.

4. Fit the PCI-Lock into the chassis to lock the ADD ON cards. Close the System Place the side door back to the original posit

Chapter 4 109This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire T650/E500 and AcerPower F5. Refer to t

110 Chapter 4Aspire E500/T650 Exploded DiagramItem Description3 OPTICAL DRIVE4 FDD WITH PANEL5 FLOPPY DISK DRIVE6 MOTHER BOARD7 HDD LOCK SLIDE8 FDD LO

Chapter 4 11116 PCI BKT17 LEFT COVERItem Description

112 Chapter 4AcerPower F5 Exploded DiagramItem Description1 3.5” COVER2 5.25” COVER3 FRONT BEZEL4 OPTICAL DRIVE5 FDD WITH PANEL6 FLOPPY DISK DRIVE7 MO

Chapter 1 5AudioT Codec : Realtek ALC880 (HD Codec)T One UAJ (Universal Audio Jack) support (rear only)Remark UAJ : UAJ not only provides the ideal so

6 Chapter 1T On-Board ConnectorsT 1 CPU SocketT 2 Memory SocketT 1 PCI Express x1 SlotT 1 PCI Express x16 Slot T 2 PCI Slots T 1 FDD SlotT 2 PATA IDE

Chapter 1 7Block DiagramSATA#1 SATA#21717SOCKET LGA775UNBUFFEREDDDR2 DIMM240-PIN DDR II DIMMX4USB-7USB-6AGTL+ P4 CPU I/FDESKTOP PRESCOTTAGTL+200MHz4

8 Chapter 1MainBoard PlacementMainboard ItemsItem Label Description1 CPU Socket LGA775 socket for Pentium 4 CPUs2 DIMM1,2 240-pin DDR2 SDRAM slots3 IR

Chapter 1 915 PANEL1 Front panel switch/LED header16 USB3,4 Front Panel USB header17 1394A2 Onboard 1394a header (optional)18 COM2 Onboard serial port

10 Chapter 1Rear I/O PortItem DescriptionPS/2 Keyboard and PS/2 Mouse ConnectorTo install a PS/2 port keyboard and mouse, plug the mouse to the upper

Chapter 1 11Jumper and Connector SettingJumper SettingJumper Type Description SettingCLR_CMOS3-pin　　　CLEAR CMOS 1-2: Normal2-3: Clear CMOSBefore clear

12 Chapter 1Connector InformationCPU_FAN/SYS_FAN/CASE FANIllustration Pin No. Definition1GND2+12V3 Sense4 Speed Control (Only for CPU Fan)ATX12VIllust

IIRevision HistoryPlease refer to the table below for the updates made on Aspire T650/E500 and AcerPower F5 service guide.Date Chapter Updates

Chapter 1 13ATX PowerIllustrationPIN No.DefinitionPIN No.Definition1 3.3V 13 3.3V23.3V 14-12V3GND 15GND4 +5V 16 PS_ON(soft On/Off)5GND 17GND6+5V 18GND

14 Chapter 1Audio1:Front Panel Audio HeaderPin No. Definition1PORT-FL2GND3PORT-FR4ACZ-DET5PORT-ER6AGND7 SENSE B8NO PIN9PORT-EL10 GNDSATA1/2/3/4: Seria

Chapter 1 15SPDIFO1:SPDIF out headerPin No. Definition1 5V analog power2 No pin3 SPDIF digital output4 Ground1394A2: Onboard IEEE 1394a headers(option

16 Chapter 17 NRTSB Request to send8 NCTSB Clear9 NRIB Ring Indicator10 KEY KeyCD_IN: Analog audio input headerPin Signal Name Definition1 CD in_L CD

Chapter 1 17Aspire T650 Front PanelNo. Description No. Description1 Optical Device 2 Floppy drive3 Power Button 4 Microphone Jack5 Speaker/Headphone J

18 Chapter 1Aspire E500 Front PanelNOTE: The picture left is the front bezel with middle cover slided down.No. Description No. Description1 Optical Dr

Chapter 1 19AcerPower F5 Front PanelNo. Description No. Description1 Optical Drive 2 Floppy Disk Drive3 Card Reader 4 Indicators5 USB Ports 6 Micropho

20 Chapter 1Aspire T650/E500, AcerPower F5 Rear PanelNOTE: The IEEE 1394 port is an optional item.No. Description No. Description1 Power Supply 2 Powe

Chapter 1 21System Peripherals The Aspire T630 and AcerPower F3 computer consist of the system itself, and system peripherals, like a mouse, keyboard

22 Chapter 1SpeakersFor systems bundled with speakers, before powering on the system, connect the speaker cable to the audioout (external speaker) por

IIICopyrightCopyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, sto

Chapter 1 23Acer eRecoveryAcer eRecovery is a tool to quickly backup and restore the system. Users can create and save a backup of the current system

24 Chapter 17. Follow the instructions on screen to complete the process.Re-install bundled software without CDAcer eRecovery stores pre-loaded softwa

Chapter 1 25Acer disc-to-disc recoveryRestore without a Recovery CDThis recovery process helps you restore the C: drive with the original software con

26 Chapter 1Hardware Specifications and ConfigurationsSystem Board Major ChipItem SpecificationSystem Core Logic ATI RC410ULI M1573Super I/O Controlle

Chapter 1 27System MemoryItem SpecificationMemory Slot Number 2 SlotsSupported Memory Size per Slot 256 MB ~ 1GBSupported Maximum Memory Size 2GB Sup

28 Chapter 1IDE InterfaceItem SpecificationIDE Controller Built-in ULi M1573IDE Controller Resident Bus PCI busNumber 40 pin PATA slot 2T Device Type

Chapter 1 29Location Rear : 4On-board header : 4USB Class Support legacy keyboard for legacy modeWake-up Event SpecificationsDevice S1 S3 S4 S5Power B

30 Chapter 100D8000-00DBFFF 16 KB I/O Expansion ROM Reserved for ROM on I/O Adapters00DC000-00DFFFF 16 KB I/O Expansion ROM Reserved for ROM on I/O Ad

Chapter 1 31NOTE: N - Not be usedNOTE: N - Not be usedIRQ Assignment MapIRQx System Devices Add-On-Card DevicesIRQ0 Timer NIRQ1 Keyboard NIRQ2 Reserv

32 Chapter 1Environmental RequirementsItem SpecificationsTemperatureOperating +5°C ~ +35°CNon-operating -20 ~ +60°C (Storage package), -10°C~+60°C (un

IVConventionsThe following conventions are used in this manual: SCREEN MESSAGESDenotes actual messages that appear on screen.NOTE Gives bits and piec

Chapter 1 33Power Management Function (ACPI support function)Device Standby ModeT Independent power management timer for hard disk drive devices (0-15

Chapter 2 35BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required setting or to active certain sy

36 Chapter 2Entering SetupOnce enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen.Use arrow keys to select

Chapter 2 37Product InformationParameter DescriptionProduct Name This item lists the product nameSystem S/N This item lists the system serial numberMa

38 Chapter 2Standard CMOS FeaturesThe following table describes the parameters found in this menu:Parameter Description OptionsDate Lets you set the

Chapter 2 39IDE Primary/Secondary/third/Fourth Master, SlaveAllows you to configure the hard disk drive connected to the master port of IDE channel.

40 Chapter 2Primary IDE MasterThis section indicate the detailed information and the related setting of the Primary IDE Master device installed on the

Chapter 2 41Advanced BIOS FeaturesThe following screen shows the Advanced BIOS Features:Enable/Disable BootSector Virus Protection.Help ItemCMOS Setup

42 Chapter 2Parameter Description OptionsVirus Warning This feature allows you to enable the VIRUS warning function for IDE Hard Disk boot sector prot

Chapter 2 43Advanced Chipset FeaturesThis page sets up more advanced information about your system. Handle this page with caution. ANy changes can aff

VPrefaceBefore using this information and the product it supports, please read the following general information.1. This Service Guide provides you wi

44 Chapter 2Integrated PeripheralsAll onboard peripherals can be set up through this menu.Parameter Description OptionsUSB 2.0 Controller Enable this

Chapter 2 45Paraller Port Address This item allows users to manually set the address for Serial Port1&Port22783783BCDisabledParallel Port Mode Thi

46 Chapter 2Power Management SetupThe Power Management menu lets you configure your system to most effectively save energy while operating in a manner

Chapter 2 47Parameter Description OptionsACPI Function This item allows you to enable or disable the ACPI functionEnabled DisabledACPI Suspend Type T

48 Chapter 2PnP/PCI ConfigurationParameter Description OptionsAllocate IRQ to PCI VGA This item allows users to enable or disable the function of allo

Chapter 2 49PC Health StatusThis section indicates the hardware information of the system including the CPU temperature, Ambient Temperature, CPU FAN,

50 Chapter 2Frequency ControlThis page helps you to set up the frequency control of the motherboard.Parameter DescriptionRatio Status You can only adj

Chapter 2 51Load Default SettingsSelecting the field loads the factory defaults for BIOS and Chipset Features which the system automatically. detects.

52 Chapter 2Set Supervisor/User PasswordWhen this function is selected, the following message appears at the center of the screen to assist you in cre

Chapter 2 53Save & Exit SetupHighlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the

1Chapter 1 System Specifications...1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .

54 Chapter 2Exit Without SavingHighlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit the

Chapter 3 55To disassemble the computer, you need the following tools:T Wrist grounding strap and conductive mat for preventing electrostatic discharg

56 Chapter 3General InformationBefore proceeding with the disassenbly procedure, make sure that you do the following:1. Turn off the power to the syst

Chapter 3 57Disassembly ProcedureThis section tells you how to disassemble the system when you need to perform system service. Please also refer to th

Aspire T650 Standard Disassembly Procedure Opening the System 1. Place the system unit on a flat, steady surface. 2. Turn

3. Remove the TV Tuner Card. 4. Remove the Modem card. Remove the Cables 1.

3. Disconnect 12V power cable “ PD” and CPU fan power cable from the M/B. 4. Disconnect the 4 Pin power cable “PE” f

7. Disconnect the “PB” power cable from the master HDD, “PC” from the slave HDD. 8. Disconnect the two HDD SATA cabl

11. Disconnect the ODD&FDD IDE and P1 power cable from the M/B connector. Remove the Memory Loose the DIMM Latch

Remove the CD-ROM, Floppy, Card-reader and HDD 1. Release the HDD-Holder, meanwhile pull the master HDD out of the chassis. 2.

2

Release the ODD-Holder, meanwhile pull the Slave ODD out of the chassis, then the Master one. Removing the USB Module Remove th

Remove the Mainboard Remove the eight screws and remove the Mainboard shown bellow. Remove the Power-supply Remove the four s

Aspire T650 Standard Reassembly Procedure Install the Power-supply Fit the Power-supply into the chassis, then fasten the four screws shown bellow.

Install the System Fan Fit the System Fan into the chassis , then fasten the four screws shown bellow. Install the SPDIF Module

Install the CD-ROM, Floppy, Card-reader Module and HDD 1.Install the master ODD into the first ODD location, then install the slave ODD into the secon

5. Install the master HDD into the second HDD location, then slide the lock handle the lock the HDD. Install the front bezel Lead t

2.Insert the memory2 into the DIMM SLOT2 shown here. Connect the Cables 1. Connect the ODD&FDD IDE and P1 power cable to the

3. Connect the LED cable ASSY to the M/B Connector. 4. Connect the two HDD SATA cables to the HDDs and M/B connector.

7. Connect the ODD IDE cable to the master & slave ODD. 8. Connect the 4 Pin power cable “PE” to the master ODD, “PF” t

11. Connect the SPDIF and AUDIO cables. Install the ADD ON Cards 1. Insert the Modem Card into the PCI SLOT3.

Chapter 1 1Overview All the new Socket-T motherboards come with a socket protector that has to be removed before you fit the CPU. This is to pr

4. Fit the PCI-Lock into the chassis to lock the ADD ON cards. Close the System Place the side door back to the original posit

Aspire E500 Standard Disassembly Procedure Opening the System 1. Place the system unit on a flat, steady surface. 2. Turn

3. Remove the TV Tuner Card. 4. Remove the Modem card. Remove the Cables 1.

3. Disconnect 12V power cable “ PD” and CPU fan power cable from the M/B. 4. Disconnect the 4 Pin power cable “PE” f

7. Disconnect the “PB” power cable from the master HDD, “PC” from the slave HDD. 8. Disconnect the two HDD SATA cabl

11. Disconnect the ODD&FDD IDE and P1 power cable from the M/B connector. Remove the Memory Loose the DIMM Latch

2. Remove the Top-cover ASSY form the chassis top. Remove the CD-ROM, Floppy, Card-reader and HDD 1. Release the HDD-Hold

4. Release the FDD-Holder, meanwhile pull the Card-reader Module out of the chassis. 5. Release the ODD-Holder, meanwhile pul

Remove the System Fan Remove the four screws and remove the system fan shown bellow. Remove the Mainboard Remove the

Aspire E500 Standard Reassembly Procedure Install the Power-supply Fit the Power-supply into the chassis, then fasten the four screws shown bellow.

2 Chapter 1ULI M1573T Provides a High Integration BridgeT One EHCI USB 2.0 and three OHCI USB 1.1 Host Controllers for supporting up to eight USB port

Install the System Fan Fit the System Fan into the chassis , then fasten the four screws shown bellow. Install the SPDIF Module

Install the CD-ROM, Floppy, Card-reader Module and HDD 1.Install the master ODD into the first ODD location, then install the slave ODD into the secon

5. Install the master HDD into the second HDD location, then slide the lock handle the lock the HDD. Install the front bezel 1. Fi

Install the Memory 1.Insert the memory1 into the DIMM SLOT1 shown here. 2.Insert the memory2 into the DIMM SLOT2 shown here.

3. Connect the LED cable ASSY to the M/B Connector. 4. Connect the two HDD SATA cables to the HDDs and M/B connector.

7. Connect the ODD IDE cable to the master & slave ODD. 8. Connect the 4 Pin power cable “PE” to the master ODD, “PF” t

11. Connect the SPDIF and AUDIO cables. Install the ADD ON Cards 1. Insert the Modem Card into the PCI SLOT3.

4. Fit the PCI-Lock into the chassis to lock the ADD ON cards. Close the System Place the side door back to the original positi

AcerPower F5 Standard Disassembly Procedure Opening the System 1. Place the system unit on a flat, steady surface. 2. Tur

3. Remove the TV Tuner Card. 4. Remove the Modem card. Remove the Cables 1.