Acer SO.ARM05.008 Datenblatt PDF herunterladen (Seite 2)

ARMC/3P

Quick Installation and Setup Guide

II. Initial Configuration

The ARMC/3P´s communication

interface is based on TCP/IP. Initially,

the ARMC/3P network interface is

configured with the parameters

shown here:

IP auto configuration: DHCP

IP address: none

Net mask: 255.255.255.0

Gateway: none

IP access control: none

If this initial configuration does not

meet your local requirements, the

following describes the initial IP con-

figuration that is necessary to access

the ARMC/3P for the first time.

II (a) Using the Psetup Tool via

Graphical User Interface

You can choose between a psetup

tool for Windows, that requires a MS

Windows 2000 and higher, and a

psetup tool for LINUX. Both can be

found on the CD delivered with this

package. You can follow the proce-

dure described below. For other OS

you may either use the serial con-

sole.

1. Connect the ARMC/3P to your

computer via local network.

2. Start the psetup tool from the CD

on the computer that the ARMC/3P is

installed or any other computer which

is part of the same local network. A

window opens as shown in Figure a)

for the Windows or b) for the LINUX

Psetup Tool.

Note: If your network provides a

properly configured DHCP server the

ARMC/3P should be automatically

assigned an IP address. Please ask

your DHCP admin for the IP address

the ARMC/3P got from the DHCP

server.

Steps for configuration:

For detecting the right MAC address

of the ARMC/3P, press the Refresh

Devices button (a) Windows

Version) or Refresh button (b)

LINUX Version) and then choose the

right MAC address in the selection

box. The displayed MAC address is

the same MAC address printed on

the white sticker placed on the back

of the ARMC/3P.

Furthermore there are two buttons:

Query Device and Setup Device.

Press the Query Device button to

display the preconfigured values of

the network configuration. The val-

ues are displayed in the text fields

located below (Windows Version)

and above (LINUX Version). If nec-

essary, adjust the network settings to

your needs. To save the changes

enter a super user name and an

according password. Then press the

Setup Device button.

To close the window and accept the

changes, press the OK button, oth-

erwise Cancel at the Windows

Version. To accept the changes

press the OK button in the new

opening window. After successful

operation you can close the LINUX

Setup window.

II (b) Running the LINUX Psetup Tool

via Command Line

To setup the ARMC/3P via Command Line

please open a command line terminal. The fol-

lowing list shows the command syntax and

their usage:

--mac <MAC address of the device>

Shows the current network

configuration.

--ip <neue IP address>

Set a new IP address.

--ipacp <dhcp|bootp|none>

Set the auto configuration.

--netmask <net mask>

Set a new netmask.

--gateway <gateway address>

Set a new gateway address.

--login <username>

Admin rights are required to

change the network configura

tion.

--pw <password>

Password of the specified

above user.

--pw-new <password>

The specified above user get a

new password.

An example shows the described commands

and their effects:

Displaying the current network settings:

test@teststation:~# /home/test/psetup --mac

00:0D:5D:00:65:78

IP auto configuration: dhcp

IP address: 192.168.5.135

Subnet mask: 255.255.255.0

Gateway: 192.168.5.1

test@teststation:~#

Changing the network settings:

test@teststation:~# /home/test/psetup

--mac 00:0D:5D:00:65:78 --ipacp none

--ip 192.168.5.55 --gateway 192.168.5.1

--netmask 255.255.255.0 --login super

--pw pass

Device configured successfully.

test@teststation:~#

II (c) Initial Configuration via Serial

Console

To configure the ARMC/3P via serial interface

both a serial port replicator cable and a null

modem cable are required. Using a serial termi-

nal, the ARMC/3P has a serial line interface

(rear bracket). This connector is compliant with

the RS 232 serial line standard. To establish a

serial connection use a standard null modem

cable. The serial line has to be configured with

the parameters belowe. When configuring with

a serial terminal, reset the ARMC/3P and imme-

diately press the ESC key. You will see some

device information, and a "=>" prompt. Enter

config, press Enter and wait for a few seconds

for the configuration questions to appear.

Bits/second: 115200

Data bits: 8

Parity: no

Stop bits: 1

Flow Control: Hardware

As you proceed, the following questions will

appear on the screen. To accept the default

values which are shown in square brackets

below, press Enter.

IP auto configuration

(none/dhcp/bootp) [dhcp]:

IP [none]:

Net mask [255.255.255.0]:

Gateway (0.0.0.0 for none) [0.0.0.0]:

a) IP autoconfiguration

With this option you can specify whether

the ARMC/3P should get its network

settings from a DHCP or BOOTP server.

For DHCP, enter dhcp, and for BOOTP

enter bootp. If you do not specify any of

these, the IP autoconfiguration is disabled

and subsequently you will be asked for

the following network settings.

b) IP address

The IP address the ARMC/3P uses.

This option is only available if IP autocon-

figuration is disabled.

c) Net mask

The net mask of the connected IP subnet.

This option is only available if IP autocon-

figuration is disabled.

d) Gateway address

The IP address of the default router for

the connected IP subnet. If you do not

have a default router, enter 0.0.0.0. This

option is only available if IP autoconfigu-

ration is disabled.

Finally, you will be asked if the values are cor-

rect, and may adjust them if necessary. After

your confirmation the ARMC/3P performs a

reset using the new values.

III Web Interface

The ARMC/3P may be accessed using a stan-

dard Java enabled web browser. You may use

the HTTP protocol or a secure encrypted con-

nection via HTTPS. Just enter the configured

IP address of the ARMC/3P into your web

browser. The initial login settings are:

Password: password

Changing these settings to user specific val-

ues is strongly recommended and can be done

on the User Settings page.

IV Remote Console

The Remote Console is the redirected screen,

keyboard and mouse of the remote host sys-

tem in which the ARMC/3P is installed. The

web browser which is used for accessing the

ARMC/3P has to supply a Java Runtime

Environment version 1.1 or higher. However,

we strongly recommend to install Sun JVM

1.5. The Remote Console will behave exactly

the same way as if you were sitting directly in

front of the screen of your remote system. That

means that both the keyboard and mouse can

be used in the usual way. Open the console

by clicking the preview picture on the main site

of the HTML frontend. The picture below

shows the top of the Remote Console.

There are some options to choose from the

menu, the important ones are the following:

Auto Adjust Button

If the video displayed is of bad quality or dis-

torted in some way, press this button and wait

a few seconds while the ARMC/3P tries to

adjust itself for the best possible video quality.

Sync Mouse

Choose this option in order to synchronize the

local with the remote mouse cursor. This is

especially necessary when using accelerated

mouse settings on the host system. In general,

there is no need to change mouse settings on

the host. *)

*) Note: At first start, if the local mouse pointer

is not synchronized with the remote mouse

pointer, press the Auto Adjust Button once.

a) for the Windows Psetup Tool:

b) for the LINUX Psetup Tool:

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Acer SO.ARM05.008 Datenblatt Seite 2

Kommentare zu diesen Handbüchern