Acer Altos G310 MK2 Bedienungsanleitung Seite 127
- Seite / 136
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
115
Troubleshooting
Problems and suggested solutions
The following table describes possible problems you might encounter,
along with suggested solutions.
Problem Suggested solution
Drives are not detected
or
The system hangs when
the adaptor ROM for
Embedded SATA
software RAID scans the
SATA ports.
• Make sure that the cable ends are
connected properly.
• Make sure that the power cables to the
drives are connected properly.
• Change cables.
• If everything fails, change the drive(s).
Operating system does
not boot.
Check the system BIOS configuration for PCI
interrupt assignments. Make sure some
Interrupts are assigned for PCI.
Make sure that you have properly selected the
Boot Device in the system BIOS setup (CMOS
Setup).
An error occurs while
reading the
configuration data on a
drive.
The drive is bad and needs to be replaced.
There is no existing RAID
configuration on any of
the drives connected to
the system and the
message “Intel
Embedded Server RAID
Technology Not
Configured” displays.
Press any key to enter the BIOS Configuration
Utility (Ctrl-E), then select a configuration
method and configure the drive(s).
BIOS reports that a
mirrored array is in
degraded mode.
Make sure all physical drives are properly
connected and are powered on.
Reconnect, replace, or rebuild any drive that
has failed.
- Acer Altos G310 Mk2 1
- FCC notice 3
- Class B equipment 3
- Laser compliance statement 4
- Important safety instructions 5
- 5 BIOS setup 49 8
- 6 Troubleshooting 79 9
- Contents 10
- Assign hot spare disk 122 11
- Initialize RAID volume 122 11
- Create RAID1 volume 121 11
- 1 System 13
- Product briefing 15
- Caring features 17
- 1 System information 18
- Product specification summary 19
- 2 System tour 21
- System board 23
- 2 System tour 24
- Item Description 24
- Front bezel 26
- Front panel 28
- Rear panel 30
- Internal components 32
- 3 Getting Started 33
- Setting up the system 35
- System startup 36
- Turning off the system 37
- Power-on problems 37
- 3 Getting Started 38
- 4 Configuring 39
- Upgrading the system 41
- Preinstallation instructions 42
- Opening the server 43
- To remove the side panel 44
- To remove the front panel 45
- 4 Configuring the system 46
- To install the Processor 48
- To remove a Processor 52
- Upgrading the system memory 53
- To remove a DIMM 55
- To install a DIMM 56
- Installing an expansion card 57
- To remove a hard disk 59
- To install a hard disk 59
- 5 BIOS setup 61
- BIOS parameters 62
- BIOS setup 63
- Entering BIOS setup 64
- 5 BIOS setup 66
- Advanced 67
- PCI Configuration 68
- Boot Configuration 69
- Peripheral Configuration 70
- Drive Configuration 71
- Floppy Configuration 73
- Event Log Configuration 74
- Video Configuration 75
- USB Configuration 76
- PCI Express Configuration 77
- Chipset Configuration 78
- Fan Control Configuration 79
- Hardware Monitoring 80
- Remote Access Configuration 81
- Security 82
- Boot Device Priority 85
- Hard disk Drives 86
- Removable Devices 87
- ATAPI CD-ROM Drives 88
- 6 Troubleshooting 91
- First steps checklist 94
- Hardware diagnostic testing 95
- Power light does not light 97
- Cannot connect to a server 100
- Problems with the network 101
- 6 Troubleshooting 102
- (Windows Operating System) 103
- LED information 105
- BIOS POST Beep Codes 107
- Appendix A: Embedded 111
- SATA RAID 111
- Technology for the 111
- Altos G310 Mk2 111
- Altos G310 Mk2 server 112
- SATA ports 113
- Driver Features 114
- Manageability/Disk console 114
- Configuring arrays 116
- Configuration strategies 116
- Assigning RAID levels 116
- Physical drive parameters 118
- Logical drive parameters 119
- Easy configuration 119
- Configuration menu screen 120
- View/Add Configuration 122
- Initializing logical drives 123
- Rebuilding failed disks 124
- Checking data consistency 125
- Troubleshooting 127
- Appendix B: 129
- Configuring SCSI/ 129
- SCSI RAID HBA 129
- Loading HBA default settings 131
- RAID volume initialization 132
- Exit and Restart the server 132
- Create RAID1 volume 133
- Assign hot spare disk 134
- Initialize RAID volume 134
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.494 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern